How to Replace the Battery in Your Samsung Galaxy Watch 4

If your Samsung Galaxy Watch 4 shows signs of a weak or dead battery, you might consider replacing it yourself. While professional help is always an option, performing a battery replacement on your own is a practical and cost-effective choice as long as you have the right tools and know-how. This guide walks you through the entire process step-by-step.

Signs You Need to Replace Your Samsung Galaxy Watch 4 Battery

Before replacing the battery, ensure your Samsung Watch 4 needs one. Common signs include:

• The watch does not hold a charge for a reasonable amount of time.
• It shuts off unexpectedly, even with a full charge.
• It takes longer than usual to charge.

If you’re experiencing any of these issues, it’s likely time for a battery replacement.

Tools Needed for Replacing the Battery

Before beginning the replacement, gather the necessary tools to avoid interruptions. Here’s a list of what you will need:

• Small screwdriver (usually a Phillips #00)
• Plastic pry tool (for opening the back cover)
• Tweezers (for handling small components)
• Replacement battery for the Samsung Galaxy Watch 4
• Adhesive (if the new battery requires it)
• A soft cloth (to protect the watch face)

Having these tools ready ensures you can complete the job without any hiccups.

How to Replace the Battery in Your Samsung Galaxy Watch 4

Follow these simple steps to replace your Samsung Galaxy Watch 4 battery and get your watch running like new again!

Step 1: Power Off the Samsung Galaxy Watch 4

Before starting, Power off the watch to avoid damage during the disassembly. To power it off:

1. Press and hold the Power button on the right side of the watch.
2. Swipe down and select Power off.
3. Wait for the watch to shut down entirely.

Once the device is powered off, you can move on to the next step.

Step 2: Remove the Back Cover of the Samsung Galaxy Watch 4

Now that your watch is powered off, you need to remove the back cover. Be careful during this step to avoid damaging any of the internal components.

• Use the plastic pry tool to carefully lift the watch’s back cover. Start at a corner and slowly work your way around the edges.
• If there are screws securing the back cover, use the small screwdriver to remove them. Place the screws somewhere safe so you don’t lose them.

Be gentle during this process, as removing the back cover can be tricky.

Step 3: Disconnect the Old Battery

Once you have removed the back cover, you should see the internal components, including the battery.

• Look for the battery connector attached to the motherboard. It may be secured with small screws or a latch.
• Use the plastic pry tool or tweezers to disconnect the battery from the watch’s motherboard carefully.

Be sure to disconnect the battery correctly before attempting to remove it.

Step 4: Remove the Old Battery

Now that the battery is disconnected, it’s time to remove it. The battery is usually held in place with adhesive.

• Use the plastic pry tool to lift the battery out of its compartment.
• If the battery is firmly stuck, you can use a hairdryer (on low) to apply a small amount of heat to loosen the adhesive. Be cautious to avoid overheating the watch.

Take your time during this step to avoid any damage.

Step 5: Install the New Battery

After successfully removing the old battery, you can install the new one.

1. Place the new battery into the same compartment as the old one.
2. Connect the new battery’s connector to the motherboard carefully.
3. If needed, apply a small amount of adhesive to secure the battery.

Ensure the battery is seated correctly and connected before moving on to the next step.

Step 6: Reassemble the Watch

Once the new battery is installed and connected, it’s time to put the watch back together.

1. Reattach the back cover of the watch.
2. If there were screws, carefully screw them back into place using the small screwdriver.
3. Press gently around the edges of the back cover to ensure a snug fit.

Step 7: Power On and Test the Watch

It’s time to power on the watch with everything back in place.

• Press and hold the Power button.
• Wait for the watch to boot up.

Once powered on, check if the battery is charging correctly and holding a charge. The new battery should improve the watch’s performance.

Troubleshooting After Battery Replacement

If your Samsung Galaxy Watch 4 doesn’t turn on after the battery replacement, try these steps:

• Double-check the battery connections to ensure everything is connected correctly.
• Make sure the battery is correctly seated in its compartment.
• If the watch still doesn’t turn on, it might be a good idea to visit a repair center to ensure that no further issues exist.

If you’re uncomfortable performing the replacement yourself or encounter any issues during the process, it’s best to seek professional help. If your warranty is still valid, contact Samsung’s customer support.

Additionally, if your watch still doesn’t work properly after replacing the battery, it could indicate a deeper internal issue that requires a technician’s expertise.

Conclusion

Replacing the battery in your Samsung Galaxy Watch 4 is straightforward as long as you have the right tools and follow the steps carefully. If you’re experiencing poor battery life or charging issues, this guide should help you replace the battery and get your watch functioning like new.

Remember, taking your time and being gentle during the process is key to avoiding damage. If you prefer, seeking professional help is always viable if you’re unsure about any step.

By following these steps, you should be able to extend the life of your watch and continue enjoying its features without interruption.

With 7+ years in SEO and blogging, I optimize reputable websites for better rankings. I’m passionate about creating detailed guides, especially in gaming and IT.

Latest posts by rizwanrkiff (see all)